Agentgates´s TPU setup with strange wavehill hump

[Mannix]

@bullsnbears
Just use the first one ..you will wind more Im sure .

@all

The problem is that those with the effect in front of them will have a different discussion than those with no means or inclination to do it.

I would like to suggest a thread that's read only for those with no physical coil.
Not a closed thread,  just so the different discussions wont get mixed up with who,s got steam and who has not...yet.

When somebody say test this or that , I wonder why they dont just make this thing and see for themselves.

If it was a difficult build I would understand it better and as we progress it may become more difficult but I doubt it.


The optimum will be only found by experimenting Physically.

Im am sure that my wind is not by any means optimum.

Thin wire for  the primary IS important (at this stage)

Thanks fatbird i will do your twin wrap

[agentgates]

quick question: when you say pulse at 50% duty cycle you mean to make a square wave from 0 volts to 30 volts (let's say) and 50% of the time, goes to 0 volts and repeat over again?

You are NOT using AC so that it would go from -30 volts to +30 volts, correct?

Correct. No AC involved at all.

@zerotensor

broli has perfectly described the problem. There are several milestones to add to the first post. Especially to the last section where it would be more than important to extend the list of safe experiments. We don't want anybody to put his lab on fire or worse.


@Stefan

I never gave you any reason to presume the bad willing. You never said that there is a deadline as there are wolfs hiding on this website in every bushes hunting for their favourite stakes: proof/prestige. You also never mentioned that there are OU-fanatics here and the only thing can cause them orgasm is light bulb on OU. If you mention this I never open this topic (especially not here) until I am 100% satisfied with my device, theories behind it, safe operation instructions, complete building tutorials, etc and is ready for mass-production.

Believe it or not the latter is the most critical and almost the hardest job as if the device is not bullet-proof when reaches the market and anybody gets only a hairline bend all the hard work was a waste of time as the BS machine mass-media will vomit the garbage that this device can "kill people". (Naturally they will not address to the multiple times higher danger of gas connected into homes and liquid explosives in cars tank with whole families sitting on it...)

Sure, when the time has arrived and I feel satisfied with it in operation, safety and look I will be more than happy to present a complete lecture with the devices, guides to build and other things to make sure nobody's going to get killed by OU-junkie overexcitement and skipping important steps.

Another thing I want to address to. When I sent you the first email with my simple question about the OU-prize/TPU together whether it would be possible my primary agenda was to find the right person. Somebody who seems a real fighter on the field and would well deserve to get this technology first hand to release. You are the founder of the OU-prize and as far as I know it was intended to protect those inventors who want to release their knowledge and technologies to the public. I said to myself this person would well deserve it to receive this device in his hand that he can carry proudly. Thing is that Stefan since I know you (a couple of days) you keep pushing your subliminal under my nose with the other OU-junkies with the "wanna see it".

I thought you are a serious and mature person who believes that the main purpose is perfection, clean air, end of wars and energy dependency. As the days passing I am starting to realize that I was wrong.

Before you or anybody else would overrun me again. I opened this topic because I know that this device works and it was the main point. I held it in my hand and doesn't make a difference in my eye whether others believe it or not. I do, because I can still think clearly that what I experienced was not OU-junkies dream. Sure it was melting the plastic, massive heatsinks, 500W-rated IGBT and needed 2 TPU stages boosted each others with caps to see light, all this from a tiny PSU. One TPU stage to 500V and the next stage to 800V to reach 190V with palm of LCs and overheating wherever you looked. All this at such a performance that is well over the limits of the used PSU.

I was not intended to go for a presentation with that pile of junk, instead in a few days time I cleaned the way of electrons to let them to go towards the load, instead of the well oversized switching ss devices and massive heatsink. Another milestone done. Decrease the consumption drammatically. Done. Next is to create more spikes. Done...

Two more things to do:
- merge the spikes safely (I already know that how to do it unsafely and keep trying to warn everybody if they reach that stage it is critical)
- voltage sense fb to keep the output constant, safe and clean without workaround like LCs and other decoration tools because it is possible, since it is a swiss watch and not a copper mining competition...

You see, in a few days time my Ambitious and Helpful Team and I have put more onto the desk on this website than anybody from the TPU Circus Team over the last 4 years - and I wont mention the understanding of theories behind the device that more and more people confirms.

Now make a comparison Stefan between my and your performance/attitude in the last couple of days.

When I saw your new masterpiece comment today I grabbed your coil and tossed it in the far corner after the ambulance took me home from the detox unit in the morning cause I was happy and eager to make it for you even by sucking the stinking ammonia of the glue for 2 days that holds it together.

I would have a respectful request to you Stefan. Sit back and read love stories or walk in the nature instead of doing things behind me out of agreement that takes away my remaining pleasure, like disabling my access to keep everybody up-to-date or just tossing your daily depression to our noses.

[CompuTutor]

I saw a simple approach to a needed variable.

I threw that idea in in case it had validity.

I was way wrong and wish to retract.



When the idea of two rings is employed,
and you turn them from natural 90 degrees,
It starts to turn "Hourglass" in the center of the side.

This occurs even though the span of wire
from the the bottom to top ring
maintains a straight path.

The variable concept I proposed,
sadly introduces a second variable too.

And it of course causes the outer secondary
to change the distance relationship with the primary.

.....It couldn't actually be sprung though, else the angle would be 90°, as the spring came to full extension.

Thank you for catching my omission,
I forgot to state the obvious need
of a retention mechanism of some sort.

There would need to be a fixation mechanism
to overcome the "Sprung" setup...



Well, I'd rather be able to toss an occasional idea in,
and have it be proven wrong by almost anyone.

Than hesitate, and have it be a missed opportunity.

So I thank you for pointing the error out,
instead of flaming me like I have seen
in other threads I read today. 

[broli]

Tony I wouldn't be too frustrated about it. Just remember the prime reason you want this technology out, some posts here are like hills you have to overcome to reach the top of the mountain. They might drag you down but they make you stronger and more confident each time. When you feel you are about to fall your companions behind you will help you continue.

Also don't forget about your health. Sleep long and plenty, eat regularly. Consider coming only once a day online at a fixed time set, after you are done for the day for example, to perhaps brief us on your progress and address people on their builds.

[Mannix]

Any body who has bothered to actually do anything with your guidance has nothing but apreciation for what you are doing.

Expectaions are the problem ..try not to have any


Thank you Tony.

Its time for your nature walk..come back soon