Pulsed DC Transformer with Embedded Magnets

[minde4000]

Minde  Your theory on the blocking diode is a good as anyones.    I can't see how Stan could create higher EMF force except by using harmonic push/pull and forced decay.  This would give only one place for that force to go,  thus the fluid medium is the absorbant.  So a blocking diode would only allow at best one half the power that should have been available.    And Minde do you have a project anywhere we can view on HHO?  OR ANYTHING?

Mr I, Thank you for your sharing your Hong Kong adventure with us!

That last post was a joke or didnt come out right   Water fracturing works somewhat by two 180 degree out of phase electrostatic forces "tearing" apart water molecules. I just wanted to emphasize 180 degree reactance of second choke. I have nothing besides Lawton PWM that everybody has and single tube SS cell/cap sprayed on with Liquit Tape (piece of crap I assume) from walmart wich gives me 32nf capacistance.  I am looking for couple of C cores so I could start building a VIC. I am sure tuning is gonna be a b..ch. But I will try anyway. I just totally ingnore all those youtube "replicators" because they have NOTHING.

All right. This aint the thread for particular subject. Lets stay on topic.

Minde

[ltseung888]

Talking to Mr. Chan, an Electronics Manufacturer

Tseung: “ Mr. Chan, how much will it cost to build the following  attached kit?”

Chan: “It depends on the quantity.  The minimum order is 1,000 units.  You want one complete, quality confirmed set and one components only package.  Is that correct?”

Tseung: “Yes.  Please give me the cost for 1,000 units.  The material cost is less than HK$20.”

Chan: “Obviously, the device will be assembled in China.  For 1,000 units, the cost will be HK$100,000.  We provide the quality control and the packaging.  For larger quantities, the cost per unit can be much lower.”

Tseung: “How soon can you deliver once I place a confirmed order?”

Chan: “If you have the final specification and all the parts identified, my factory can finish the 1,000 unit order within 4 weeks.  You have to deposit 50% of the price first.”

Tseung: “Can you provide me with a dozen samples first?”

Chan: “Sure.  You have to put down HK$10,000 first.  We can then provide you with a dozen professionally made samples.”

*** The DIY Kit will confirm overunity.  Should I get it done professionally now?  Should I wait for the publicity at the Inno Tech Design Expo 2010?  Should I wait for the Christmas Tree Demo first?

[Pirate88179]

Lawrence:

Please, no offense intended but, have you considered what many Chinese manufacturers have done to US companies that go to them to get products made at a lower cost?

I am not condemning the Chinese people here, nor all Chinese manufactures, ok?  But, there is a long history of folks going to some of these people and having their product produced, only to find that later, they are selling it for half of what they are charging as a per unit cost as the folks are paying....and it is their design.

Google this if you do not believe me but, if they think it is a viable product, they may jump into the market with tens of thousands of units while you struggle to pay for the initial 1,000.

Again, please, this is not a slam on the Chinese people in any way.  We have plenty of "business" folks here in the US that would do the same thing if given the opportunity.

Bill

[ltseung888]

Lawrence:

Please, no offense intended but, have you considered what many Chinese manufacturers have done to US companies that go to them to get products made at a lower cost?

I am not condemning the Chinese people here, nor all Chinese manufactures, ok?  But, there is a long history of folks going to some of these people and having their product produced, only to find that later, they are selling it for half of what they are charging as a per unit cost as the folks are paying....and it is their design.

Google this if you do not believe me but, if they think it is a viable product, they may jump into the market with tens of thousands of units while you struggle to pay for the initial 1,000.

Again, please, this is not a slam on the Chinese people in any way.  We have plenty of "business" folks here in the US that would do the same thing if given the opportunity.

Bill

Thank you, Bill.  Since I do not consider this as my invention and I do not need the income, I may ask for the following deal.

1.   They can take the design and produce the DIY kit as their own product at their own expense.
2.   Give me 12 free samples so that I can send to some famous Universities for further verification.
3.   When and if they make money, donate 10% of the profit to charitable organizations.  I recommend Help Seedlings Innovate Foundation Limited.
4.   The offer is not exclusive.  I can make the same offer to other manufacturers in China or aboard.
5.   I may even let them copy my book (it will be free and on-line in any case).  They can put it on a CD to reduce cost and provide more multimedia information.  Some foreign manufacturers may translate the information into their own language.

I expect many will wait for the publicity at the Inno Tech Expo 2010 and/or the academic verifications from the top Universities.  Few will act now.  But many will jump in as soon as some make very handsome initial profit.  The World will benefit.

Many will improve and build the FLEET reading lamps.  I may not need to come up with money of my own or beg for investment.  This may be the path set out by the Almighty. 

[XS-NRG]

you have exactly one month left for the 1000 Watt unit...