Quote from: CRANKYpants on November 24, 2008, 08:52:40 PM
WHAT NO KNEE-DEEP?

         @ . . @
          (-------)
          < I    I >             
            "   "
T

Sorry..... KneeDeep.....By the way, that's a good likeness!

Quote from: hoptoad on November 24, 2008, 10:44:28 PM
As for input being irrelevant, well it would be, if the input power cost nothing. But I don't get my electricity for nothing (or any other driving engine fuel), so as a consumer, it matters to me. If I spent 100 watts to get 1 watt out, it will matter very little to me how fast the generator / motor is turning, because I've just lost 99 watts for the pleasure of watching a rotor / motor spin whilst performing no other visibly useful mechanical or electrical work for that 99 watt loss.
Cheers

START WITH A COIL THAT DECELERATES THE PRIME MOVER WHILE PROVIDING 1 WATT.
CREATE A COIL THAT ACCELERATES THE PRIME MOVER WHILE PROVIDING 1 WATT.

IMPROVE THE DEIGN SUCH THAT THE DECELERATION IS NOW GIVING ONLY 0.25 WATTS
AND THE ACCELERATION IS PROVIDING 10 WATTS.

IGNORE ALL AND BE HAPPY.

SHARE

INGNORE ALL AND BE HAPPY.

T

Hi Thane,
why don´t you just use a heavy flywheel
as the drive to test your devices ?

Then you can exactly measure,if the flywheel
will accelerate or slow down...

Will free you of all uncertainities about the drivemotor..

Just give the flywheel a good spin, measure its RPM
via a laser meter and see, if it spins up
or slows down, when you engage your coils.

Good luck.

Regards, Stefan.

Quote from: hartiberlin on November 26, 2008, 05:38:23 AM
Hi Thane,
why don´t you just use a heavy flywheel
as the drive to test your devices ?

Then you can exactly measure,if the flywheel
will accelerate or slow down...

Will free you of all uncertainities about the drivemotor..

Just give the flywheel a good spin, measure its RPM
via a laser meter and see, if it spins up
or slows down, when you engage your coils.

Good luck.

Regards, Stefan.

THANKS FOR THE SUGGESTION STEFAN BUT WE GET THE SAME EFFECT FROM A DC MOTOR.- SO THERE IS NO UNCERTAINTY.

ALSO ME HAVE MADE HUNDRED OF COILS AND MADE THOUSANDS OF TESTS - THE INDUCTION MOTOR SLIP ANGLE CURRENT READING CANNOT BE FAKED OR MISREAD BECAUSE WE MONITOR IT RIGHT DOWN TO 0.001 AMPS.

WE ARE A BUSINESS - IN BUSINESS TO DEVELOP AND MARKET THE BEST REGENERATIVE ACCELERATION COILS POSSIBLE - NOT TO MAKE A PERPETUAL MOTION MACHINE ALTHOUGH THIS WOULD BE GRAVY.

OUR COMMITMENT TO OUR INVESTORS IS TO ENSURE WE I_RON OUR OUR DESIGN AND PRODUCE THE BEST WE CAN - IT IS A SLOWER PROCESS - BUT BASED ON WHAT I HAVE SEEN OVER THE PAST NINE MONTHS (ON THIS FORUM AND ELSEWHERE) - EVEN IF WE WERE PRODUCING 7.2 WATTS OUT WITH 5.3 WATTS INTO OUR DC MOTOR I WOULDN'T MENTION IT OPENLY.

OUR GOAL IS MAINSTREAM SCIENCE ACCEPTANCE - WE HAVE THE THEORY AND THE DEMO AND ARE GAINING THE TRUST - THIS IS NO TIME TO HAVE ANOTHER "HEINS DEMOS PERPETUAL MOTOIN TO MIT" ARTICLE.

CHEERS
THANE

Quote from: TheBuzz on November 26, 2008, 01:09:40 AM
Hi Thane,

First let me say you da man! Love what you are doing and how you are doing it.

I would like to replicate the bi-toroid and will post my results and anything I can add. Can you point me at a good starting place for the details?

Thanks

THIS IS AN EXCELLENT PLACE TO START, I THINK THERE IS A WAY TO READ ONLY MY POSTS?
SO GO THROUGH THEM AND READ AND LEARN - IT IS ALL THERE...

GOOD LUCK AND HAVE FUN! (IT OUGHT TO BE DIFFICULT BUT FUN AND EDUCATIONAL)

CHEERS
Thane