Overunity.com Archives is Temporarily on Read Mode Only!



Free Energy will change the World - Free Energy will stop Climate Change - Free Energy will give us hope
and we will not surrender until free energy will be enabled all over the world, to power planes, cars, ships and trains.
Free energy will help the poor to become independent of needing expensive fuels.
So all in all Free energy will bring far more peace to the world than any other invention has already brought to the world.
Those beautiful words were written by Stefan Hartmann/Owner/Admin at overunity.com
Unfortunately now, Stefan Hartmann is very ill and He needs our help
Stefan wanted that I have all these massive data to get it back online
even being as ill as Stefan is, he transferred all databases and folders
that without his help, this Forum Archives would have never been published here
so, please, as the Webmaster and Creator of these Archives, I am asking that you help him
by making a donation on the Paypal Button above.
You can visit us or register at my main site at:
Overunity Machines Forum



SPIRAL MAGNET MOTOR IDEA??

Started by magnetman12003, February 14, 2009, 01:48:55 PM

Previous topic - Next topic

0 Members and 2 Guests are viewing this topic.

Print
Go Down Pages 1 2 3 4 5 6
User actions

sushimoto

#10
February 15, 2009, 08:57:40 AM
Quote from: magnetman12003 on February 14, 2009, 07:59:20 PM
Hi You are right about the flywheel. I plan to use a heavy flywheel should I attempt to construct this device

I already pointed out the crank arm will not work as shown in my crude illustration..

If you start replicating it, it would be a good idea,
to start progressing at the same point, where the video has ended.
... Instead of bringing in new elementary principles.
The "Follower Disk" must not make a full revolution
in order tu fulfill its purpose. It does not even need to be a full disk.
The Crankarm was just to swing the magnet out of the "sticky point".

best,
sushi
DAMIT DAS MOEGLICHE ENTSTEHT, MUSS IMMER WIEDER DAS UNMOEGLICHE VERSUCHT WERDEN.

magnetman12003

#11
February 15, 2009, 07:32:14 PM
Hi Guys,

Thanks for all the input. I already rounded up gears and after some more parts right now.  Looking into that one way bearing also.

I am going to give this a try as it seems by looking at the movie it might just work. I guess the magnet spiral design has to be just right also.  By using a heavy flywheel and some powerfull magnets maybe I can keep the spiral moving continuously??

Tom

magnetman12003

#12
February 20, 2009, 10:04:10 PM
Hi Guys,
I purchased a couple of gears and a thought occured to me.  I dont want this to be under powered so I plan to use larger powerful magnets. My problem is space. The next illustration comes to mind which is not in keeping with the spiral concept but if you look hard it works the same way using different polaritys,

I have many powerfull 1.5 inch long .75 inch diameter cylinder magnets.   I have a diameter of 4 inches to work within using those magnets inside the gear teeth..
Illustrated is a plan I think might work??

The LEFT disk has zero or "NO BACK LASH" and is free to turn "ONLY" counterclockwise because a one way clutch bearing is used on its shaft.      Thats the one way follower disk.

The RIGHT disk shaft is secured to a heavy flywheel.  Thats the driver disk and is completely free to turn. In this case clockwise.

Remembering what is stated above can you see this turning continuously?  Observe direction arrows. Teeth are meshed together on both disks.  Both disks pivot in the center.

Open for opinions.

Tom

sushimoto

#13
February 22, 2009, 08:12:08 AM
Hi,

FYI look at this magnetman.

http://www.youtube.com/watch?v=kDvPTzJAQV0&feature=related

best regards,
sushi
DAMIT DAS MOEGLICHE ENTSTEHT, MUSS IMMER WIEDER DAS UNMOEGLICHE VERSUCHT WERDEN.
Print
Go Up Pages 1 2 3 4 5 6
User actions