Overunity.com Archives is Temporarily on Read Mode Only!



Free Energy will change the World - Free Energy will stop Climate Change - Free Energy will give us hope
and we will not surrender until free energy will be enabled all over the world, to power planes, cars, ships and trains.
Free energy will help the poor to become independent of needing expensive fuels.
So all in all Free energy will bring far more peace to the world than any other invention has already brought to the world.
Those beautiful words were written by Stefan Hartmann/Owner/Admin at overunity.com
Unfortunately now, Stefan Hartmann is very ill and He needs our help
Stefan wanted that I have all these massive data to get it back online
even being as ill as Stefan is, he transferred all databases and folders
that without his help, this Forum Archives would have never been published here
so, please, as the Webmaster and Creator of these Archives, I am asking that you help him
by making a donation on the Paypal Button above.
You can visit us or register at my main site at:
Overunity Machines Forum



HHO heaters design questions

Started by ydeardorff, May 09, 2012, 03:13:01 PM

Previous topic - Next topic

0 Members and 2 Guests are viewing this topic.

Print
Go Down Pages1 2 3 ... 6
User actions

ydeardorff

May 09, 2012, 03:13:01 PM
I am working on a hho home heater.

My question is what flame tip to use. Id like to use a liquid cpu cooler system, but fear the flame would melt right through it.

Has anyone experimented with nozzle tips and flame length? I saw one person using a ball inflator tip as a nozzle. The flame was very small, but would that be too small?

Anyone know the limits to these cpu coolers and how much heat they can handle? I have some ceramic permeable cups I could use to diffuse the flame and spread the heat a bit.

I purchased a welding back flash arrester, and a set of jewelers welding tips sizes 1, 2, and 3 to test out. Hopefully I can make the hot section of this heater very small, but with a decent output.

The prospect of heating for less than 400 watts is VERY tantalizing.

Mark69

#1
May 09, 2012, 08:20:11 PM
Try this guy's videos on youtube.  He says he has adjustments to get the flame size you need.
Mark

http://www.youtube.com/watch?v=36lEXocd1BM

or more from smartscarecrow.  These guys put out some power!

www.youtube.com/watch?v=2p_T-AoBqCo&feature=plcp

ydeardorff

#2
May 09, 2012, 09:41:20 PM
Yes I have talked with HHO connection.

The adjustments are done via the PWM. Im looking to control the flames maximum point via the nozzle, then dial it down from there as needed.

Mark69

#3
May 10, 2012, 08:23:59 AM
I would use the nozzle that gets you the biggest flame possible, then put some kind of valve on the supply tube, to cut back the flow rate.  That will reduce your flame size.  Think of it like an oxygen/ acetelene (sp) torch.  These have a round knob at the base to control the flow of one of or both of the gases, I forget which, to control the flame.

Paul-R

#4
May 10, 2012, 10:58:40 AM
Quote from: ydeardorff on May 09, 2012, 03:13:01 PM
I am working on a hho home heater.

My question is what flame tip to use.
If you are using pure stochoimetric HHO, the flame speed is supersonic
and you will end up blowing yourself and possibly neighbours from
here to eternity.

Pure HHO is VERY DANGEROUS INDEED.

You could mix in another gas, maybe air, but if this mixing process should
fail, then you are back on a death trip.

How are you generating the HHO? There may be (probably will be)a better
way to get to where you want to be.
Print
Go Up Pages1 2 3 ... 6
User actions