Overunity.com Archives is Temporarily on Read Mode Only!



Free Energy will change the World - Free Energy will stop Climate Change - Free Energy will give us hope
and we will not surrender until free energy will be enabled all over the world, to power planes, cars, ships and trains.
Free energy will help the poor to become independent of needing expensive fuels.
So all in all Free energy will bring far more peace to the world than any other invention has already brought to the world.
Those beautiful words were written by Stefan Hartmann/Owner/Admin at overunity.com
Unfortunately now, Stefan Hartmann is very ill and He needs our help
Stefan wanted that I have all these massive data to get it back online
even being as ill as Stefan is, he transferred all databases and folders
that without his help, this Forum Archives would have never been published here
so, please, as the Webmaster and Creator of these Archives, I am asking that you help him
by making a donation on the Paypal Button above.
You can visit us or register at my main site at:
Overunity Machines Forum



1939 Gravity Power - multiply power by 1200%

Started by cipbranea, May 21, 2014, 01:38:08 AM

Previous topic - Next topic

0 Members and 18 Guests are viewing this topic.

Print
Go Down Pages 1 ... 43 44 45 46 47 ... 105
User actions

gotoluc

#220
June 15, 2014, 10:21:58 PM
Starting to see some building action. Thanks for sharing Shylo and Craigy.

Today I was able to connect the upper shaft to the lower and found that the offset between upper and lower shaft I pointed out and incorporated in my build does not work if both shafts are centered.
That will delay the test by one day as I now have to go back to the welder to make a modification.
If I can get it welded tomorrow then I should be able to do the test and do a video by Tuesday.

Stay tuned

Luc

shylo

#221
June 17, 2014, 06:21:26 PM
Hi All, was trying different weights ,turbo your right the build needs work, the bottom bearing blew apart, but only after I added a load.
The drive that enters the translation plate, needs to be fixed but offset, the lower needs to rotate in a fixed position. ( Artoj drawing is pretty much bang on , the early ones)
When adding a load, the lower shaft and weight slow down but will catch up if you add the load gradually.
My build is just for trying to figure out how everything works, not to put into mass production.
By adding extra weight the pressure on the lower bearing increased dramatically , This may be part of the reasons for having 4 offset weights , to distribute it evenly?
Thanks for your time. artv

gotoluc

#222
June 17, 2014, 08:22:36 PM
Seems kind of quiet around here?

Got one video done but where I'm living at this time the internet bandwidth is very limited, so video uploading is very slow and can cut off at any time, then you got to start all over again. To help get it done I divided the video demo in two parts.

Here is the first part: https://www.youtube.com/watch?v=00xIxEQqRsk&feature=youtu.be

The next part may be in two hours or more. Also, this video is unlisted, so you need the link to watch it.

Luc

AB Hammer

#223
June 17, 2014, 08:34:23 PM
gotoluc

Grease your pillow block around the edge. Otherwise nice construction. Looking forward to your test.

Alan
With out a dream, there can be no vision.

Alan

gotoluc

#224
June 17, 2014, 08:43:33 PM
Quote from: AB Hammer on June 17, 2014, 08:34:23 PM
gotoluc

Grease your pillow block around the edge. Otherwise nice construction. Looking forward to your test.

Alan

Do you think grease will work better than oil?

Luc
Print
Go Up Pages 1 ... 43 44 45 46 47 ... 105
User actions