Overunity.com Archives is Temporarily on Read Mode Only!



Free Energy will change the World - Free Energy will stop Climate Change - Free Energy will give us hope
and we will not surrender until free energy will be enabled all over the world, to power planes, cars, ships and trains.
Free energy will help the poor to become independent of needing expensive fuels.
So all in all Free energy will bring far more peace to the world than any other invention has already brought to the world.
Those beautiful words were written by Stefan Hartmann/Owner/Admin at overunity.com
Unfortunately now, Stefan Hartmann is very ill and He needs our help
Stefan wanted that I have all these massive data to get it back online
even being as ill as Stefan is, he transferred all databases and folders
that without his help, this Forum Archives would have never been published here
so, please, as the Webmaster and Creator of these Archives, I am asking that you help him
by making a donation on the Paypal Button above.
You can visit us or register at my main site at:
Overunity Machines Forum



Self Running Micro TPU, with closed loop.

Started by EMdevices, November 12, 2007, 11:49:58 PM

Previous topic - Next topic

0 Members and 3 Guests are viewing this topic.

Print
Go Down Pages 1 ... 76 77 78 79 80 ... 139
User actions

wattsup

#385
December 08, 2007, 01:14:30 PM
@btentzer

I think CTG Labs is right. I saw the same thing with my CBC as mobius just makes a short. You have x volts coming in but most is consumed by the mobius looping leaving not enough for the led. Did you try increasing the applied voltage but put a resistor before the led if you do this since it will blow.

I don't think mobius is useful here since it will cancel the field especially is the winds are one on top of the other. You need the field to impart magnetism through the ferrite, back and forth to the trigger.

Mannixs' design is somewhat mobius but the coils are not over each other. This may have a different effect.

I just got myself one good sized transformer and will try this on my Mini TPU circuit. Just by pulsing 3 volts DC on the 110volts primary and releasing sends sparks out about 2 inches from the spark point. Never saw that with the regular toroid. This transformer has a lot of mass and I want to see how it will react to the circuit. Will let you know.

4Tesla

#386
December 08, 2007, 03:11:04 PM
Bruce,

Have you tried 2 cores like in the graphic?

4Tesla

4Tesla

#387
December 08, 2007, 03:18:05 PM
@plengo
Have you done anymore testing with you rechargeable battery circuit?

4Tesla

Bruce_TPU

#388
December 08, 2007, 03:32:08 PM
Hey guys,

No I haven't tried this on two separate cores yet.  That will be for another day.

I had my circuit, as shown in the schematic several posts back, except I wound over the bottom windings with two top windings.  Each winding having two ends.  I then hooked the ends, crossing in the middle with two IN002 diodes.  NONE of the new winding wires were attached anywhere on the circuit.  Circuit runs fine, but no extra time gained.  I reversed one of the diodes, and the LED would not light.  I then removed the diode, and the LED starts to blink, without the cap needing to be recharged.  Somehow, the second windings stopped the flow of current in the windings underneath.

On a side note, my son's light sabre broke beyond repair this morning.  I slid out the 21 LED stack and plugged it into the circuit,  ;D all 21 blinked away, with no power hookup.  I went to recharge the system and time it and when I touched my leads to the battery, some of the LED's glowed then smoked.  Yet one LED is fine.  Any thoughts on why a stack of 21 would possibly have some fry when 9volt is touched?

Holiday Cheers,
Bruce
1.  Lindsay's Stack TPU Posted Picture.  All Wound CCW  Collectors three turns and HORIZONTAL, not vertical.

2.  3 Tube amps, sending three frequency's, each having two signals, one in-phase & one inverted 180 deg, opposing signals in each collector (via control wires). 

3.  Collector is Magnetic Loop Antenna, made of lamp chord wire, wound flat.  Inside loop is antenna, outside loop is for output.  First collector is tuned via tuned tank, to the fundamental.  Second collector is tuned tank to the second harmonic (component).  Third collector is tuned tank to the third harmonic (component)  Frequency is determined by taking the circumference frequency, reducing the size by .88 inches.  Divide this frequency by 1000, and you have your second harmonic.  Divide this by 2 and you have your fundamental.  Multiply that by 3 and you have your third harmonic component.  Tune the collectors to each of these.  Input the fundamental and two modulation frequencies, made to create replicas of the fundamental, second harmonic and the third.

4.  The three frequency's circulating in the collectors, both in phase and inverted, begin to create hundreds of thousands of created frequency's, via intermodulation, that subtract to the fundamental and its harmonics.  This is called "Catalyst".

5.  The three AC PURE sine signals, travel through the amplification stage, Nonlinear, producing the second harmonic and third.  (distortion)

6.  These signals then travel the control coils, are rectified by a full wave bridge, and then sent into the output outer loop as all positive pulsed DC.  This then becomes the output and "collects" the current.

P.S.  The Kicks are harmonic distortion with passive intermodulation.  Can't see it without a spectrum analyzer, normally unless trained to see it on a scope.

4Tesla

#389
December 08, 2007, 04:42:15 PM
Too much current.. I isolate the cap from the circuit when I recharge it.

4Tesla
Print
Go Up Pages 1 ... 76 77 78 79 80 ... 139
User actions