RESONANCE EFFECTS FOR EVERYONE TO SHARE

[otto]

Hello all,

@Groundloop

thaks a lot but I have my 3 oscillators. Im an electronics guy so its not a problem for me to build all the electronics stuff. Thanks again.

Im only reading what you all are building, testing....great work so far.

I wish you all a great success in the next year and for myself I wish to solve the TPU "secret". Is it really a "secret"??

Otto

[gotoluc]

I am so glad to see the work of my friends. IMPRESSIVE!

Happy new years to all.

@gotluc,
thank you again for your excellent work and desire to serve all. (can you call me sometime this year 2008??)

@Groundloop
thank you for your excellent work on this thread and many others (one of them that I have been) (Hows the snow in your country?, I have been in Finland last month,  it was beautiful people and place all over, I even met some nice  people from Norwegian).

Now,

can you @gotluc, setup a final version or versions of different setups we have so far on the FRONT PAGE where we can just look at and keep up the changes up to date? so that people can replicate to the latest or to the latest that matters as a step foward?

So far I see 5 versions that people can replicate and make observations from:
   1) the one you @gotluc found out in the beginning (manual switching)
   2) version 2 where Groundloop offers a solid-state of the step 1)
   3) version 3 where some members have point-out improvements on 2)
   4) Groundloop's PIC microcontroller version to come on January 2009
   5) a new changed version from 3) (I think???) with more improvements

do you guys see what I see?

We MUST get more organized (no criticism to anyone here at all, please )

Lets allow all the versions on board but at the same time all controlled to new comers and old comers like me.

Fausto.

Hello Fausto my friend ,

glad you are here . I know what you're saying about it being sometimes difficult to follow. I may even start a new topic instead of modifying or adding to my past post since Stefan has expressed before that he prefers to keep posts original for archive sake.

@everyone, at this point I would recommend for you all to use just a Signal Generator and get familiar with the effects of resonance and how inductance, frequency and capacitance interplay. We can do all this with just the  signal generator output and the beauty is it doesn't blow up like like the higher voltage circuits can and you still can use a scope and look at forms at these lower input voltages but once we use higher voltages I have found my scope and other instrument become affected and no longer give correct readings. Once we know more what direction we want to take after better understanding the effect then we can start using the circuit to amplify the effect we wish to use.

Video Tutorial 2 gives you the basic tools needed to experiment at this time. Also, if you use your inductance, capacitance meter make sure you don't have a coil at resonance operating (on) since your meter will give false readings ... we learn the hard way

As I find new effects I will share by video.

Thank you all for your interest and sharing.

Luc

[gotoluc]

Hello all,

@gotoluc

Very nice work!!

Otto

Thank you Otto for your positive input

Luc

[wattsup]

@plengo

I like the clap gif. Are you the guy in the first row? lol

@otto

I will have a revised diagram in January for the FTPU that will be more complete. Maybe it will give you some other ideas.

@gotoluc

Just as a side note, I tried finding the resonance of my outer coil for my ElectoSwingMagnet - ESM (in the Power Ratio Over One thread) using my FG that goes up to 2mhz and I have NOT found the resonance. This is the first time for me not to find it. I have tried this with so many other coils. The bulb stays on all the time. Hmmmm. @gyuslan suggested I use a special device but do not have access to one and still think if I cannot find it the traditional way, no device will. Hmmmm again. I ordered a new FG that will give more output power.

I will have some good coiling ideas for January in testing this circuit.

@groundloop

Thanks for the rar. I opened it and found the proper gif but the Eagle file will not open. There is an error all the time saying it cannot find the file and no other options. But the file is in fact there. Weird. Maybe I will have to re-install the program. Can the program just export a parts list that could be posted here in text format. Otherwise I will have to take it off the gif which is hard to see all the R values and all. Sorry for this.

[Groundloop]

@Wattsup,

I have tested that the files open in the newest Eagle version. It is just a little tricky.
First start Eagle and create a new folder, then create a project folder inside that folder.
Now, exit eagle. Find the new project folder and copy the files into that folder.
Now, re open the Eagle program. The files should be in the new folder.

Eagle has a export function, go to file and export and select part list.
The part list will open in wordpad, word or the windows text editor.

NB: Sometimes I use parts that has the correct layout and pin assignment, but
       has renamed the parts. Do not fully trust the part list. Also check the cad drawing.
       The first two rows is always correct.

Groundloop.