Overunity.com Archives is Temporarily on Read Mode Only!



Free Energy will change the World - Free Energy will stop Climate Change - Free Energy will give us hope
and we will not surrender until free energy will be enabled all over the world, to power planes, cars, ships and trains.
Free energy will help the poor to become independent of needing expensive fuels.
So all in all Free energy will bring far more peace to the world than any other invention has already brought to the world.
Those beautiful words were written by Stefan Hartmann/Owner/Admin at overunity.com
Unfortunately now, Stefan Hartmann is very ill and He needs our help
Stefan wanted that I have all these massive data to get it back online
even being as ill as Stefan is, he transferred all databases and folders
that without his help, this Forum Archives would have never been published here
so, please, as the Webmaster and Creator of these Archives, I am asking that you help him
by making a donation on the Paypal Button above.
You can visit us or register at my main site at:
Overunity Machines Forum



Self Running Micro TPU, with closed loop.

Started by EMdevices, November 12, 2007, 11:49:58 PM

Previous topic - Next topic

0 Members and 13 Guests are viewing this topic.

Print
Go Down Pages 1 ... 81 82 83 84 85 ... 139
User actions

4Tesla

#410
December 11, 2007, 02:22:44 AM
@plengo

I built the two transistor oscillator circuit.. It works.

4Tesla

Bruce_TPU

#411
December 11, 2007, 08:17:13 PM
Hey guys,

Thank all of you for the traveling wishes. 

I am back at home and at the bench.  First experiment was a bust, with the mini motor.  It ran fine  while the 9volt was connected, but died the moment the leads were released.  So that is a no go, no way.  Just not enough current available.  I had tied it into the same location as my LED.

Right now I am testing a LC setup with the two control wires.  I want to try this set up again, using only one turn of each wire, a bit larger diameter wire, for less resistance.   ;)

I also picked up my mini solar cell today.  That will be a fun future test also!   

I will keep you posted if (when) something interesting develops.

Holiday Cheers,
Bruce
1.  Lindsay's Stack TPU Posted Picture.  All Wound CCW  Collectors three turns and HORIZONTAL, not vertical.

2.  3 Tube amps, sending three frequency's, each having two signals, one in-phase & one inverted 180 deg, opposing signals in each collector (via control wires). 

3.  Collector is Magnetic Loop Antenna, made of lamp chord wire, wound flat.  Inside loop is antenna, outside loop is for output.  First collector is tuned via tuned tank, to the fundamental.  Second collector is tuned tank to the second harmonic (component).  Third collector is tuned tank to the third harmonic (component)  Frequency is determined by taking the circumference frequency, reducing the size by .88 inches.  Divide this frequency by 1000, and you have your second harmonic.  Divide this by 2 and you have your fundamental.  Multiply that by 3 and you have your third harmonic component.  Tune the collectors to each of these.  Input the fundamental and two modulation frequencies, made to create replicas of the fundamental, second harmonic and the third.

4.  The three frequency's circulating in the collectors, both in phase and inverted, begin to create hundreds of thousands of created frequency's, via intermodulation, that subtract to the fundamental and its harmonics.  This is called "Catalyst".

5.  The three AC PURE sine signals, travel through the amplification stage, Nonlinear, producing the second harmonic and third.  (distortion)

6.  These signals then travel the control coils, are rectified by a full wave bridge, and then sent into the output outer loop as all positive pulsed DC.  This then becomes the output and "collects" the current.

P.S.  The Kicks are harmonic distortion with passive intermodulation.  Can't see it without a spectrum analyzer, normally unless trained to see it on a scope.

Motorcoach1

#412
December 11, 2007, 08:44:18 PM
@ btentzer >Ã,  Ã,  Ã,  Ã,  Ã,  Ã,  Ã,  http://babelfish.yahoo.com/translate_url?tt=url&trurl=http%3A%2F%2Fdigilander.libero.it%2Faltraenergia%2Fmarinov.html&lp=it_en&.intl=us&fr=b1ie7Ã,   you may find this arcive interesting , It seems to have been lost but someone posted it on the net I would make a copy before it's gone again. The date is interesting too !!

4Tesla

#413
December 11, 2007, 09:00:16 PM
Quote from: 4Tesla on December 11, 2007, 12:21:53 AM
@wattsup

Not yet.. I'm going to call tomorrow and see what the status is.. I never bought anything from this company before.. I found them through Google.. I hope they are real.

4Tesla

Didn't call in time.. they close at 4pm EST and I'm in the PST zone, so I have to call before 1pm..  I saw on their site that it can take up to 15 days before they ship.. plus shipping time.. up to three weeks to get the parts.. only two weeks for me so far..  If I remember, I'll try to call before 1pm tomorrow.

4Tesla

4Tesla

#414
December 11, 2007, 10:13:07 PM
I don't have my toroids yet.. but have been playing with LED circuits and just verified that running LEDs in series takes less current to run.. each time I add another LED it takes 2-4 less mA to run the circuit.. I have reduced the current by 10mA by just adding more LEDs in series.. it doesn't seem to effect the brightness of the LEDs.  I found that running the LEDs in parallel doesn't reduce the circuit current.  I would have thought since you are lighting more LEDs that the circuit current would go up and not down.  Does anyone know why it goes down?  Something to do with the diode voltage drop?

Thanks,
4Tesla
Print
Go Up Pages 1 ... 81 82 83 84 85 ... 139
User actions