Overunity.com Archives is Temporarily on Read Mode Only!



Free Energy will change the World - Free Energy will stop Climate Change - Free Energy will give us hope
and we will not surrender until free energy will be enabled all over the world, to power planes, cars, ships and trains.
Free energy will help the poor to become independent of needing expensive fuels.
So all in all Free energy will bring far more peace to the world than any other invention has already brought to the world.
Those beautiful words were written by Stefan Hartmann/Owner/Admin at overunity.com
Unfortunately now, Stefan Hartmann is very ill and He needs our help
Stefan wanted that I have all these massive data to get it back online
even being as ill as Stefan is, he transferred all databases and folders
that without his help, this Forum Archives would have never been published here
so, please, as the Webmaster and Creator of these Archives, I am asking that you help him
by making a donation on the Paypal Button above.
You can visit us or register at my main site at:
Overunity Machines Forum



Self Running Micro TPU, with closed loop.

Started by EMdevices, November 12, 2007, 11:49:58 PM

Previous topic - Next topic

0 Members and 16 Guests are viewing this topic.

Print
Go Down Pages 1 ... 80 81 82 83 84 ... 139
User actions

Bruce_TPU

#405
December 10, 2007, 12:44:21 AM
@ Sanmankl

I forgot to add the diode on the negative side of the 1.5 uf cap.  It is facing the negative.  Weird I know, but it added time.   ;)  I posted some time ago about it and forgot to update it to the circuit.

@ All
I am out of town for a short bit, and then I will be back experimenting.  I have some more experiments to run with my two control wires still.  After that I will tie in a mini 1-3volt motor I found today.  I will glue a magnet on the shaft and attempt to spin that in the center of the toroid while the LED blinks, with no battery hooked up, just used to kick start.  Also, I will be purchasing a small solar cell, and place this above the LED's and then tie that back into the starting position.  It should make for some fun experimenting if nothing else!   ;D

Once I have finished with all of the above, I will unwrap my control wires from the toroid, and wrap two additional toroids in the configuration that Mannix gave.  The only difference I will make is that the wrapping will be bifilar, and I will but some other type of wire around the circumference, underneath.  (You never know, eh?  LOL)

I still say that SM's secret is in the very specific frequencies and their intersection.  IMHO.  There is more than that, but that with tubes, is really the starting place.  But for my non EE self, this is fun, and educational. 

Holiday Cheers,
Bruce
1.  Lindsay's Stack TPU Posted Picture.  All Wound CCW  Collectors three turns and HORIZONTAL, not vertical.

2.  3 Tube amps, sending three frequency's, each having two signals, one in-phase & one inverted 180 deg, opposing signals in each collector (via control wires). 

3.  Collector is Magnetic Loop Antenna, made of lamp chord wire, wound flat.  Inside loop is antenna, outside loop is for output.  First collector is tuned via tuned tank, to the fundamental.  Second collector is tuned tank to the second harmonic (component).  Third collector is tuned tank to the third harmonic (component)  Frequency is determined by taking the circumference frequency, reducing the size by .88 inches.  Divide this frequency by 1000, and you have your second harmonic.  Divide this by 2 and you have your fundamental.  Multiply that by 3 and you have your third harmonic component.  Tune the collectors to each of these.  Input the fundamental and two modulation frequencies, made to create replicas of the fundamental, second harmonic and the third.

4.  The three frequency's circulating in the collectors, both in phase and inverted, begin to create hundreds of thousands of created frequency's, via intermodulation, that subtract to the fundamental and its harmonics.  This is called "Catalyst".

5.  The three AC PURE sine signals, travel through the amplification stage, Nonlinear, producing the second harmonic and third.  (distortion)

6.  These signals then travel the control coils, are rectified by a full wave bridge, and then sent into the output outer loop as all positive pulsed DC.  This then becomes the output and "collects" the current.

P.S.  The Kicks are harmonic distortion with passive intermodulation.  Can't see it without a spectrum analyzer, normally unless trained to see it on a scope.

4Tesla

#406
December 10, 2007, 01:00:32 AM
Bruce,

Have a safe trip and talk to you when you get back.

4Tesla

wattsup

#407
December 10, 2007, 10:43:50 PM
@btentzer

Have a good trip.

@4tesla

Did you get any word form your parts supplier. I ordered some stuff there also a week ago and still no news. Anyways, they did not touch my credit card yet, so I  guess they will when they ship my order.

sanmankl

#408
December 10, 2007, 10:54:07 PM
@Bruce,

Thanks for the diode update. I haven't got round to duplicate your setup yet but will soon enough. Have a safe trip.

So far, my best times based somewhat on EM's circuit (RC cap changed to 200nF, LED to negative) is 34m 50s.
Seems like there's still a way to get longer run if the torriod size/type-wire size/type gets into proper "harmony"?

My latest is a torriod core of about 40mm size, Fe (black in colour) with AWG#20 wire. I'm in a way lucky. I can walk into one of my regular electronic component shop and pick various size torriods for cheap. Paid something like USD1 for the 40mm Fe ring.

Cheers, cp

4Tesla

#409
December 11, 2007, 12:21:53 AM
@wattsup

Not yet.. I'm going to call tomorrow and see what the status is.. I never bought anything from this company before.. I found them through Google.. I hope they are real.

4Tesla
Print
Go Up Pages 1 ... 80 81 82 83 84 ... 139
User actions