Thane Heins Perepiteia.

[CRANKYpants]

HERE'S THE DEAL PEEPS,

I AM WORKING 12-14 HOURS PER DAY, EVERY DAY TRYING TO GET A NEW PROTOTYPE FINISHED AND I CAN'T KEEP UP WITH THE REQUESTS FOR THIS THAT AND THE OTHER THING - SORRY NO KIDDING

PERHAPS PEOPLE CAN ASK blisteringanomaly SINCE HE SHOULD BE CLOSE TO BE UP AND RUNNING WITH HIS NEW STUFF?

ALSO I COULDN'T GET THE TESTS DONE TODAY EITHER - SINCE I WAS GIVING A DEMO.

SORRY AGAIN
T 

PS
MIKE ARE YOU OR YOUR BROTHER COMING TO THE LAB SOMETIME?

[CRANKYpants]

Greetings,

@ Thane...
Please consider conducting "my" simple experiment with the battery that I have proposed few months ago. I have no doubt that it will show real gains coming out of your setup and it should quiet the PB types for a while but without disturbing your work schedule.

Such an experiment will not be difficult at all to conduct.

1. Get a car battery that is fully charged.
2. Connect it to the DC or AC motor.
3. Observe a run time.

Then

4. Recharge the battery.
5. Connect it to the DC or AC motor that employs your coil setup.
6. Observe a run time.

Such a run will give you a very impressive material to show to the business executives that do not care about technical details or Electrical Engineering. 

DEAR ADLEP,

YOU ARE GOING TO GET YOUR WISH - BUT NOT FROM ME.

THE PROTOTYPE I AM CURRENTLY BUILDING IS A 4 COIL UNIT WHICH WILL BE RUN UP TO FULL SPEED AND MAY OR MAY NOT GO BEYOND THE 3600 MAX SPEED RATING OF THE MOTOR - WE WILL HAVE TO WAIT AND SEE ABOUT THAT. I AM BUILDING A 1/2 INCH BULLET PROOF LEXAN CASE FOR TESTING JUST IN CASE IT WANTS TO PULL A "GOTOLUC - EXPLODING NEO SHITSTORM".

IT IS HOWEVER, INTENDED TO PRODUCE MORE POWER (ACROSS A LOAD - HOPEFULLY 40 - 50 WATTS/COIL @ 200 WATTS)
THAN WHAT THE MOTOR WILL BE CONSUMING AT CLOSE TO ZERO SLIP @ 90 WATTS OR LESS..

THEY PEOPLE WHO ARE GETTING IT WILL THEN RECTIFY THE OUTPUT, FEED IT INTO A BATTERY AND THEN RECTIFY IT AGAIN BACK TO 60 HZ AC AND TRY TO SELF RUN THE SYSTEM. THEY ALSO WANT TO USE A DC MOTOR AS WELL I THINK.

SO ALMOST EVERYBODY WILL BE SATISFIED SOON I HOPE? 

CHEERS
T

[LarryC]

DEAR ADLEP,

YOU ARE GOING TO GET YOUR WISH - BUT NOT FROM ME.

THE PROTOTYPE I AM CURRENTLY BUILDING IS A 4 COIL UNIT WHICH WILL BE RUN UP TO FULL SPEED AND MAY OR MAY NOT GO BEYOND THE 3600 MAX SPEED RATING OF THE MOTOR - WE WILL HAVE TO WAIT AND SEE ABOUT THAT. I AM BUILDING A 1/2 INCH BULLET PROOF LEXAN CASE FOR TESTING JUST IN CASE IT WANTS TO PULL A "GOTOLUC - EXPLODING NEO SHITSTORM".

IT IS HOWEVER, INTENDED TO PRODUCE MORE POWER (ACROSS A LOAD - HOPEFULLY 40 - 50 WATTS/COIL @ 200 WATTS)
THAN WHAT THE MOTOR WILL BE CONSUMING AT CLOSE TO ZERO SLIP @ 90 WATTS OR LESS..

THEY PEOPLE WHO ARE GETTING IT WILL THEN RECTIFY THE OUTPUT, FEED IT INTO A BATTERY AND THEN RECTIFY IT AGAIN BACK TO 60 HZ AC AND TRY TO SELF RUN THE SYSTEM. THEY ALSO WANT TO USE A DC MOTOR AS WELL I THINK.

SO ALMOST EVERYBODY WILL BE SATISFIED SOON I HOPE? 

CHEERS
T

Outstanding T, a great effort on your part and very much looking forward to your results.

Regards, Larry

[hoptoad]

.........Now what if you can improve that generator so it can produce 4400 watts using a 1 hp weed eater engine. You are now talking about using a lot less gasoline to produce the same amount of energy. See it does not have to be OU to be very beneficial.

Bad example hydrocontrol, because 746 watts equals 1 horsepower, so if you were able to get 4400watts from a 1 horsepower weed eater, then you would be getting 6 times more output than input, which would obviously be OU.

Cheers

[LarryC]

Bad example hydrocontrol, because 746 watts equals 1 horsepower, so if you were able to get 4400watts from a 1 horsepower weed eater, then you would be getting 6 times more output than input, which would obviously be OU.

Cheers

So Hoptoad, according to your theory, now that I purchased a 16 seer heat pump and saving over $150 on average a month over the old 10 seer unit then I must be getting OU and not an increase in efficiency So please explain!

Regards, Larry