Kapanadze Cousin - DALLY FREE ENERGY

[magpwr]

Did you measured little moustashes (current) with current transformer or maybe with resistor ?

Did you wound your bifilar like Tesla setup or Hooper setup. There is big difference between !!
Lenght of bifilar 18,75m (half of grenade).

This is important - Your second oscillogram at 22.18.43 is very important and very similar to Ruslan.
Watch his video again from 1.04 and compare yourself. He has on top of positive and negative peaks small humps. It means you have significant phase error in your setup.

I need some time to redraw Brutto schematic as i think it should be !! 

Picture for compose one's thoughts.

hi Enjoykin,

I may like Brutto drawing of the circuit diagram as you have shown us.

But Brutto have not produced any working device yet.

People are still using 1/4 and 1/8 resonance for this device.I think they are mixing up this with Don Smith device which is base on 1/4 wave.

Why isn't there anyone else besides me whom realized for Akula video it's all about the Harmonics or Sub-harmonics.30th Harmonics and 60th Harmonics for new device.

In order to see perfect frequency alignment only 30th harmonics and 60th harmonics is suitable .2 reasons one is to fit within yoke core capability to around 75khz and another fit within air-core capability not below 18khz as mentioned by Akula.

In the old Akula video tela coil tuning video .The frequency derive from his sprecturm analyser is 165khz and another signal is 55khz .

Use the attached Harmonics calculator it reveal "1650900hz" as 30th harmonics for 55030hz.This is to see prefect frequency alignment besides 60th harmonics.

This is the last time i will be talking about harmonics.

[itsu]

Did you measured little moustashes (current) with current transformer or maybe with resistor ?

Did you wound your bifilar like Tesla setup or Hooper setup. There is big difference between !!
Lenght of bifilar 18,75m (half of grenade).

This is important - Your second oscillogram at 22.18.43 is very important and very similar to Ruslan.
Watch his video again from 1.04 and compare yourself. He has on top of positive and negative peaks small humps. It means you have significant phase error in your setup.

I need some time to redraw Brutto schematic as i think it should be !! 

Picture for compose one's thoughts.

I measured the current with my AC/DC current probe, see video.
I wound my bifilar coil in the hopper way as we had no indication it was wound any other (Tesla) way.
My bifilar is about half (16m) of my grenade (32m) coil

Like a said before, i put my current probe in severall positions (main grenade leads, bifilar coil leads, 3 turn secondary leads, 28 turn secondary leads etc.) but never did i see the same
current trace (little moustache) as Ruslan showed.

Will see tomorrow for further actions/tests.

Regards Itsu

[Enjoykin]

My variant of Ruslan device. 

to Itsu
Now i will watch your video. Thank you and good luck !!

Reg.

[John.K1]

Can anybody give me some info about that small coil right behind the Tesla coil?. It is some turns OPPOSITE to Tesla . It is under the red tape.    (7:13 ,   https://www.youtube.com/watch?v=KN-ZmCW0W8w  ) ??

Cheers

[Void]

Can anybody give me some info about that small coil right behind the Tesla coil?. It is some turns OPPOSITE to Tesla . It is under the red tape.    (7:13 ,   https://www.youtube.com/watch?v=KN-ZmCW0W8w  ) ??
Cheers

Hi John. I don't think Ruslan has commented on why he did this yet, or at least I haven't
seen any translations where Ruslan explains why he did this. 
Ruslan may only have done this because he was replicating closely what Akula did.
It may be to try to isolate the tesla coil secondary somewhat from loading by the
big antenna coil. Not sure though.  May be for some other purpose entirely.
All the best...